Schedule Here

The author is making a number of great annotation about A Step-by-Step Guide to Installing a Bathtub as a whole in this great article directly below.

Mounting a bath tub isn't specifically rocket science, but it does require solid plumbing, woodworking, and also sometimes, tiling skills. Replacing an old tub with a new one is likewise a moderately tough job. If the old bathtub is readily accessible, the project can relocate easily; if you have to open a wall surface to get rid of the old bathtub as well as position the new bath tub, the job is much harder. In either case, the project is within a residence handyman's abilities, although you will need an assistant to leave the old bathtub and set in the brand-new one. See to it you have certified yourself for the work as well as are comfortable attempting it. As opposed to employing a contractor to take control of a halfway-completed project, it is far better to think about using one before you start. Possibilities are you might need a specialist plumber to make tube connections.
This post will certainly help you set up a new bath tub in your bathroom if you have actually already bought a brand-new bathtub and also don't need to change the setup of your previous water system pipes.
Your devices as well as material list need to comprise the following:

• New Bathtub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Chisel


• Tape Measure


• Pipeline Caps


 

Getting ready for the Installment

To start with, the sustaining frame provided with the bathroom must be fitted (if needed) according to the maker's guidelines. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is important to see to it that if the faucet includes a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is likewise practical to fit a supporting plate under the faucets unit to stop stress on the tub.
Fit the flexible faucet connectors to the bottom of both taps using 2 nuts and olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet with the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Make sure you use all of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bath should now prepare to be suited its last placement.

Removing Old Touches

If you need to replace old taps with new ones as a part of your setup, then the first thing you should do is separate the water supply. After doing so, turn on the taps to drain pipes any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be quite bothersome due to the limited gain access to that is often the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipelines to the faucets. Have a fabric all set for the staying water that will come from the pipelines. Once the supply pipelines have actually been eliminated, make use of the same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary taps from turning throughout this procedure. Once the taps have been gotten rid of, the holes in the bath/basin will have to be cleansed of any old securing compound.
Before carrying on to fit the new taps, compare the pipe connections on the old taps to the brand-new faucets. If the old taps are longer than the new taps, after that a shank adapter is required for the brand-new faucets to fit.

Installing the Bath tub

Utilizing both wood boards under its feet, position the bath tub in the called for setting. The wood boards are useful in uniformly spreading the weight of the tub over the location of the boards instead of concentrating all the weight onto 4 tiny points.
The following objective is to guarantee that the bath tub is leveled all round. This can be achieved by checking the spirit level and adjusting the feet on the bathtub until the spirit level reads degree.
To mount faucets, fit the bottom of the outermost versatile tap port to the ideal supply pipe by making a compression join; then do the exact same for the various other tap.
Turn on the water and check all joints and also new pipework for leaks and also tighten them if necessary. Load the tub as well as additionally examine the overflow outlet and the typical outlet for leakages.
Ultimately, fix the bath paneling as explained in the producer's user's manual. Tiling as well as securing around the bath tub must wait till the bathtub has been used a minimum of once as this will certainly resolve it right into its last placement.

Suitable New Taps

If the tails of the new taps are plastic, after that you will require a plastic connector to avoid damage to the thread. One end of the adapter fits on the plastic tail of the tap and also the various other end gives a link to the existent supply pipes.
If you require to fit a monobloc, then you will call for lowering couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next off, position the faucet in the placing opening in the bath/basin making certain that the washing machines remain in area in between the tap and the sink. Secure the faucet in position with the supplier offered backnut. As soon as the tap is firmly in place, the supply pipes can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with typical faucet connectors. The former type needs to be linked to the faucet ends first, tightening up just by hand. The supply pipes can later be linked to the various other end. Tighten both ends with a spanner after both ends have been connected.

Tiling Around the Tub

In the area where the bath satisfies the tile, it is essential to secure the accompanies a silicone rubber caulking. This is necessary as the installation can move enough to split a rigid seal, creating the water to pass through the wall in between the bathroom and also the tiling, resulting in complications with dampness as well as possible leakages to the ceiling below.
You can pick from a range of coloured sealants to assimilate your components as well as installations. They are offered in tubes as well as cartridges, and also are capable of securing gaps approximately a size of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to always fill the bathtub with water prior to sealing, to permit the activity experienced when the tub remains in usage. The sealant can break fairly very early if you do not take into account this activity before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are likewise easily readily available on the marketplace. It is suggested to fit the floor tiles using waterproof or water resistant glue as well as cement.

A Step-by-Step Guide to Installing a Bathtub

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

 

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

 

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

Remove the Existing Bathtub

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

 

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

Choose the Right Bathtub

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

Install the Plumbing and Ledger Board

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

 

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

Install the Bathtub

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

 

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

 

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

Hook up the Plumbing

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

Install the Bathtub Surround

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

 

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

 

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

 

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

I hope you enjoyed our article on How to Install a Bathtub Yourself. Thanks a ton for taking time to read through our blog. Do you know someone else who is truly interested in A Step-by-Step Guide to Installing a Bathtub? Please feel free to share it. Thanks so much for taking the time to read it.

Immediate plumbing assistance for emergencies.